1H NMR Analysis (SIMCA)

From Powers Wiki
Revision as of 05:23, 3 October 2012 by Bozhang (talk | contribs)


1H NMR Analysis (SIMCA)

Excel Processing

Secondary observation ID labels can be added by inserting a blank second row and filling in the desired labels. This does NOT affect the raw data. It merely makes “viewing” easier in the SIMCA output.

Note:

Use the standard method to remove instrument noise. Click here [1] for details.

For PLS-DA analysis, the y-variable values are placed in a row below the row containing the last NMR integral bucket value. When the spreadsheet is transposed in SIMCA, this last row becomes the last column.

After noise removal, the data should be autoscaled. By default, SIMCA-P will use "UV" autoscale the imported data set.

PCA Analysis

1. Start a “new” project by opening the desired integral table spreadsheet

2. Click on new project icon

3. Select the desired Excel file

4. Click “Open”

5. Click on the comma option. The data formatting should now look correct

6. Click “OK”

7. Project type should be SIMCA-P Project

8. Click “next” button

9. Respond “No” to the question regarding the one row that is “empty or contains only text”

  It is the row of labels that was inserted using Excel. You can delete the blank row to avoid this. 

10. Use the “Commands” button (bottom left) to “transpose” the data set.

   The rows should now correspond to a given NMR spectrum.  Each row is an “observation”. The integral values contained in each row are referred to as “variables”.

11. Click on the button at the top of the column to set the first column as the “primary observation ID’s”

   It may already be labeled as primary

12. Click on the “Observation IDs primary” button

   The observation IDs should now be color coded with the observation ID primary color. If secondary observation IDs were inserted using Excel, then click on the second column button and then click on “Observation IDs secondary”. Again, the column should be color coded to the correct color (light yellow).    

12. Click on the butoon for the first row

   It may already be labeled as primary and then click on the “Variable IDs primary” button to color code the first row (green).  Next, repeat for the second row containing the ppm ranges that define each bucket. These will be the “Variable IDs secondary” and are turquoise.  Click “Next” button in the lower-right. 

13. Click the “Finish” button

14. Exclude the solvent region and “ends” of the spectra

15. Highlight the desired rows by dragging the cursor along the top set of buttons and then click the “exclude” button (along the left edge)

16. Repeat for each desired region

17. Click “Next” then click “Finish”

18. Using the menu bar, click on the “autofit” button.

   This should calculate the first and second primary components.  Additional components can be calculated using the “Calculate next component” button.  

19. View the results, click on the “Create four overview plots” button.

   This produces the “Score Scatter” plot in the upper-left hand corner. The lower-left hand corner contains the “Loading Scatter” plot.  

20. Expand the score scatter plot for better viewing.

21. Click on data point

22. Right-click and choose “Properties”

23. Choose the color tab and choose coloring type by “identifiers”

   The default then is to color by secondary observation IDs.  This uses the labels inserted using Excel.  If desired, change the default colors. 

24. Click “Apply”.

25. Click “OK”.

PLS Analysis

1. The data are prepared in an Excel file as described above.

2. The Excel file is opened in SIMCA as described above for PCA analysis.

3. The opened file should then be transposed. Again, the commands button found in the lower left provides access to this command.

4. The label information for observations and variables should be processed as described for PCA analysis above.

5. The difference between the PCA approach and the PLS approach occurs with labeling of the variables (i.e., the bucketed intensities and the discriminator values).

6. The region containing the bucketed intensities is highlighted.

 These values are labeled as “x-variables” by clicking on the VARIABLE button in the left hand frame and choosing x-variables.  

7. Next, the discriminator values should be set as 1 or 0.

  Normally, "0" is assigned to wild-type or control group while "1" is assigned to mutant or treatment group.  

8. Selected data may still be excluded prior to the statistical analysis.

9. The dataset is “fit”, additional components can be added/substracted and the results are visualized using the same commands as for PCA analysis described above.

OPLS-DA Analysis

1. This approach applies orthogonal signal correction prior to PLS analysis. I need to do more reading… But, I believe that I have basic command sequence needed to explore the approach using SIMCA-P+ Version 12.0.

2. Start from an Excel file that has NOT been noise corrected and NOT been autoscaled.

3. The data file should be first analyzed using either PCA or PLS as described above.

4. The analysis is reportedly hindered by extreme outliers found in PCA 2D scores plot (where did I read this…?...the Umetrics manual maybe…). So, any outliers should be removed prior to OPLS analysis.

5. Open the Excel file in SIMCA, go to the Dataset pull-down menu. Choose Spectral Filters. In the available column, scroll down and select OCS. Press the button labeled as => to move OCS into the selected column.

6. Click OK.

7. The OSC panel should appear. Refer to your NMR spectral data to identify bins that contain strong peaks for metabolites (e.g., citrate peaks in mouse urine spectra).

8. Highlight several of these bins (maybe 5-10).

9. Click on Y to change the state of these to Y values. Click on the “Next >” button. There may be a message regarding exclusion of variables with no variance.

10. The result, both in terms of the scores plot and the plots showing the difference between PC score points, depends which peaks are assigned as the Y values.

11. A new OSC panel will appear.

   There should be a table with columns labeled No, Angle in Degreees, Remaining SS in % and Eigenvalue. 

12. Click on the “next component” button. Generally, two components are recommended by Umetrics.

13. Click on the Next button.

14. Check the destination folder and file name. Click on the “Finish” button.

15. Read and close the OSC message box.

16. The current model will probably say “PLS <unfitted>” in the Type column. Fit the data using the usual commands for autofit and plot visualization

17. Go the Analysis pull-down menu and select Change Model Type.

18. From the list, choose OPLS/O2PLS.

19. Choose the Analysis pull-down menu and select Autofit (…or just use the Autofit button on the toolbar).